- Видеонаблюдение
-
Охранная сигнализация
- Мини сигнал
- Беспроводные охранные системы
- GSM
- Централи
- Датчики PIR
- Датчики комбинированные PIR+MW
- Датчики разбития стекла
- Датчики магнитные
- Датчики ударные
- Датчик затопления
- Датчики газа
- Датчики температуры
- Пожарные датчики
- Охрана периметра
- Устройства анти нападения (кнопки)
- Aксессуары
- Сигнализаторы акустически,оптические
- Сигнализационные кабеля
- Контроль доступа
- Переговорные системы
- Пожарные системы
- Видеодомофоны и домофоны
- Автоматика для ворот и шлагбаумы
- Сетевое оборудование
- Системы оповещения
- Коммутационные и серверные шкафы, аксессуары
- Инструменты
- Кабели, укрыватели, трубы и принадлежности
- Аккумуляторы, трансформаторы, блоки питания
- HDMI
- Аксессуары для караванов и кемперов
- Электромонтаж
- Солнечная энергия
- Ветровая энергия
- Контакты
REM3 Hand-Held Two-Way Remote Keypad
Features
Compatible with MG5000, MG5050, and Spectra SP series V3.00 (or higher) and RTX3 V1.31 (or higher)
Supports StayD
System Status Memory: The REM3 will keep the last system status received from the control panel in memory. Momentarily press the Info button to display the last system status--even when out of range. Used to confirm the last action you did on the system while away from the system.
Configure which partitions the REM3 arms/disarms
Built-In Transceiver (433MHz or 868MHz)
Independent Arm, Sleep, Stay and Off buttons and LED display per partition
Control up to 6 PGMs and/or generate panics
Keypad Mode: Requires code entry
Remote Mode: One-touch arming / Disarming
Installer Diagnostic Mode:
Partition 1 LEDs = Signal Strength Display
Partition 2 LEDs = RF Interference Display
Provides visual and auditory feedback of system status
Press the Status button to receive system status
Label to identify remote control owner
Compact, water-resistant design
Size: 8cm x 3.4cm x 1.5cm (3.1in x 1.3in x 0.6in)
EN50131 grade 3
Compatible with MG5000, MG5050, and Spectra SP series V3.00 (or higher) and RTX3 V1.31 (or higher)
Supports StayD
System Status Memory: The REM3 will keep the last system status received from the control panel in memory. Momentarily press the Info button to display the last system status--even when out of range. Used to confirm the last action you did on the system while away from the system.
Configure which partitions the REM3 arms/disarms
Built-In Transceiver (433MHz or 868MHz)
Independent Arm, Sleep, Stay and Off buttons and LED display per partition
Control up to 6 PGMs and/or generate panics
Keypad Mode: Requires code entry
Remote Mode: One-touch arming / Disarming
Installer Diagnostic Mode:
Partition 1 LEDs = Signal Strength Display
Partition 2 LEDs = RF Interference Display
Provides visual and auditory feedback of system status
Press the Status button to receive system status
Label to identify remote control owner
Compact, water-resistant design
Size: 8cm x 3.4cm x 1.5cm (3.1in x 1.3in x 0.6in)
EN50131 grade 3